series am6q-z 6 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.c 1 of 3 north america only features: ? rohs compliant ? ? wide 2:1 input range ? ? high efficiency up to 86% ? ? continuous short circuit ? models single output model input voltage (v) output voltage (v) output current max (ma) isolation (vac) max capacitive load(uf) efficiency (%) AM6Q-0503SZ 4.5-9 3.3 1000 500 1000 73 am6q-0505sz 4.5-9 5 1000 500 1000 76 am6q-0512sz 4.5-9 12 500 500 500 79 am6q-0515sz 4.5-9 15 400 500 400 79 am6q-1203sz 9-18 3.3 1000 500 1000 76 am6q-1205sz 9-18 5 1200 500 1200 81 am6q-1212sz 9-18 12 500 500 500 85 am6q-1215sz 9-18 15 400 500 400 85 am6q-2403sz 18-36 3.3 1200 500 1200 73 am6q-2405sz 18-36 5 1200 500 1200 80 am6q-2412sz 18-36 12 500 500 500 84 am6q-2415sz 18-36 15 400 500 400 86 am6q-4803sz 36-75 3.3 1200 500 1200 74 am6q-4805sz 36-75 5 1200 500 1200 80 am6q-4812sz 36-75 12 500 500 500 84 am6q-4815sz 36-75 15 400 500 400 85 models dual output model input voltage (v) output voltage (v) output current max (ma) isolation (vac) max capacitive load(uf) efficiency (%) am6q-0512dz 4.5-9 12 250 500 250 82 am6q-0515dz 4.5-9 15 200 500 200 82 am6q-1212dz 9-18 12 250 500 250 88 am6q-1215dz 9-18 15 200 500 200 88 am6q-2412dz 18-36 12 250 500 250 88 am6q-2415dz 18-36 15 200 500 200 88 am6q-4812dz 36-75 12 250 500 250 87 am6q-4815dz 36-75 15 200 500 200 88 note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. input specifications parameters nominal typical maximum units voltage range 5 4.5-9 vdc 12 9-18 24 18-36 48 36-75 filter (pi) network start up time 20 ms no load input current 45 ma input reflected current 20 ma
series am6q-z 6 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.c 2 of 3 north america only isolation specifications parameters conditions typical maximum units tested i/o voltage 3sec 500 vac resistance 50 mohm capacitance 500 pf output specifications parameters conditions typical maximum units voltage accuracy 1 % cross regulation (dual output models) 25% load on one output ? 100% load on the other output 5 % over voltage protection zener diode clamp 5 6.2 v 12 15 15 18 12 15 15 18 over current protection fl 185 % short circuit protection continuous short circuit restart auto recovery line voltage regulation ll-hl 0.5 % of vin load voltage regulation load:0-100% unbalanced 1 % temperature coefficient 0.02 %/ o c ripple & noise 20mhz bandwidth 75 mv p-p minimum load current 0 % of max general specifications parameters conditions typical maximum units switching frequency 100% load 330 khz operating temperature derating above 60oc -40 to +85 o c storage temperature -40 to +125 o c maximum case temperature 100 o c cooling free air convection humidity 95 % rh case material nickel coated copper weight 25 g dimensions (l x w x h) 1.75 x 1.10 x 0.28 inches 44.50 x 28.00 x 7.00 mm mtbf >1.28mhrs ( mil-hdbk -217f, ground benign, t=+25c ) transient recovery deviation 3 % safety specifications parameters standards designed to meet iec/en 60950-1 pin out specifications pin single dual 1 -v input -v input 2 +v input +v input 3 +v output +v output 4 np common 5 -v output -v output np: not populated
series am6q-z 6 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.c 3 of 3 north america only dimensions 28.00 (1.10) 6.60 (0.26) 4.40 (0.17) 2.70 (0.11) 3.84 (0.15) 10.16 (0.40) 15.24 (0.60) 10.16 (0.40) 7.00 (0.28) derating note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com.
|
